Seashell SS-i Quick Setup Guide Manual do Utilizador descarregar pdf

1. Lens Window

2. Lens Ring

3. Button A

4. Button B

5. Button C

6. Button D

7. Lock

8. Lock Button

9. Lens Hood Cover

10. Side Spacer

11. Front Spacer

12. Strap Mount

13. Brace Hole

14. Lock Hinge

15. Button A - Rubber Head

16. Button B - Rubber Head

17. Button C - Rubber Head

18. Button D - Rubber Head

19. Cushion Holder

20. Back Foam Cushion

21. O-Ring

22. Hinge

23. O-Ring Grease

#2#2

iPhone 3G / 3GS

#2#2

iPhone 4 / 4S

Insert the Front Spacer into the four cushion

slots on the front housing. Please be sure that

the Front Spacers are properly affixed.

Adjust your iPhone

in a dry surface before loading it to SS-i:

- Insert the Side Spacer into the slots on the camera

case’s front housing.

- Place the iPhone

into the front housing and check

that the Side Spacers (on two sides) can keep the

iPhone

in place properly. Replace the Side Spacers as

necessary.

Install Front Spacer

Install Side Spacer

Test before Use

Installing iPhone

Test the Operation of the iPhone

Load the iPhone

into

Seashell SS-i

Flip the Lock to close

the housing

Pull the lock to test if it is

secured

• Ensure the inside surface of SS-i is clean and dry without

installing the iPhone

• ClosethecaseandiptheLocktothefrontofhousing.Push

gently and lock.

• Putthehousingintoatleast200mmdeepwaterfor5minutes.

• Checkifthereisanywaterseepageinsidethehousing.

• If there is no water leak, take out the housing, dry it with a

towel.

• SettheiPhone

to camera function and load the iPhone

into

the housing.

• Repeatthestepstolockthehousingbeforeputtingittowater.

• Checkifthebuttonfunctionsareworkingwhileinwater.

Pre-installation Preparation

Components

Preparation of iPhone

Seashell iPhone

Waterproof Photo Housing

Quick Setup Guide

•Seashell iPhone

 Waterproof Photo Housing is suitable to different models of iPhone

. List of

supportedmodelscanbefoundfromoursite(http://www.seashell.hk/).

•Some spacers are pre-set in SS-i to directly load iPhone

 4 / 4S models. Illustrated below is the

recommendedsizesofSideandFrontspacesforiPhone

3G,3Gs,4&4SwithoutaniPhone

jacket.

•iPhone

withajacketcanfitintoSS-ibyadjustingthesizesofspacers.

•While configuring youriPhone

intoSS-i housing,leavesome spaces betweentheiPhone

and

thespacers.UserdonotneedtofittheiPhone

tothehousingtootightly.SS-ihousingcanwell

enclosedtheiPhone

.

Please refer to the User Manual for detailed installation steps.

*Beforeoperatingoradjustingthisproduct,pleasereadtheentireUserManual.

#

 Thecopyrightofthetrademark“iPhone”isheldbyAppleInc..

a. Make sure the battery has enough charge.

b. Make sure the iPhone

has enough memory.

c. Make sure the touchscreen of the iPhone

operates well.

d. Set the iPhone

to Airplane Mode and switch off all

alarms and notifications.

e. Set the iPhone

Auto-Lockfunctionto“Never”.

f. MovetheCameraicontothebottomrightcornerofthe

screen.

g. Adjust the brightness of the iPhone

screen to the

highestlevel.

h. Lock the Portrait Orientation to make sure the screen

does not auto-rotate.

i. Set the iPhone switch off the flash (iPhone

4/4S).

j. Ifyouneedtouseotherphotofunctions,followthe

instructions released from Apple Inc. to manage photos

andvideoinyouriPhone

IfyouhavefinishedallthepreparationforSS-ihousingand

iPhone

,youcanloadtheiPhone

into the housing.

* The Camera icon should be the end of right and do not move Mail or

Message at the left side of these icons when moving the four icons to

the bottom right corner. It is wrong procedure, but push Button D before

goes to photo taking mode by pushing Button C, the message screen

will display for the confirmation. The iPhone* should be unloaded to

clear this message.

Quick Setup Guide 1

Resumo do Conteúdo

Página 1 - Quick Setup Guide

1. Lens Window2. Lens Ring3. Button A4. Button B5. Button C6. Button D7. Lock8. Lock Button9. Lens Hood Cover10. Side Spacer11. Front Space

Comentários a estes Manuais

Sem comentários

Seashell SS-i Quick Setup Guide Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para PDAs Seashell SS-i Quick Setup Guide. SeaShell SS-i Quick Setup Guide User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com PDAs Seashell SS-i Quick Setup Guide